Can I Install a Tub Myself? Considerations And Also Steps
Can I Install a Tub Myself? Considerations And Also Steps
Blog Article
Right here down the page you will discover some wonderful news in relation to Tools You Need to Install a New Bathtub .
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is readily easily accessible, the task can relocate quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub and likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has been used at least when as this will certainly settle it into its final placement.
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I hope you enjoyed reading our article about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to browse our article. Appreciated our blog entry? Please share it. Help someone else locate it. I thank you for reading our article about How to Install a Bathtub Yourself.
Get Started
Report this page